工程师个人的英文简历模板范文

在准备中文简历的时候多为自己准备一份英文简历也许会对给面试官留下好的印象哦!以下是关于工程师个人的英文简历模板，欢迎浏览!

　　Basic information:

Name: 范文稿 Gender: Male

DOB: November 28, 1984 Height: 176cm

Present address: East Hengshan Road, Fengman District, Jilin City Marital status: Single

Graduation school: Yanbian University

Major: Mechanical Layout, Manufacturing and Automation Tel.:*E-mail: *

Position to be appointed: Process technology engineer Education and training:

2004.8—2008.6, Jilin Province Yanbian University, majoring in mechanical layout (CET Band 4, Computer Test Grade 2)

2001.8—2004.6, studied at the Jilin Province Lishu County Senior Middle School

1998.8—2001.6, studied at the Jilin Province Lishu County Taiping Middle School

　　Working experience:

Aug. 2008—now, I have been working at the Jilin Automobile Co., Ltd. of FAW

　　Introduction:

I. Aug. 2008-Dec. 2008，I practiced in all production workshops to know about stamping, painting and welding and process technology of auto of fitting shop.

II. Dec. 2008-Jan. 2010, I was engaged in production control in production department and promotion of lean production. I followed improvement experts who have made site improvement and guidance on Dong’an Auto Engine and Shulan General Machinery for half a month. I could master in elementary knowledge of lean production. I could grasp preparation methods of operation manual and essentials book and working procedure capacity list. And I was in charge of site 5S management of all workshops and daily improvement.

III. Jan. 2010-now, I have been working as site engineer of fitting shop in charge of site technology management and maintenance of standard operation. I participated in change of circle time of workshop and establishment from circles such as workers, machine, stuff to project layout and made follow-up, implementation and confirmation of policies. I amended standard operations of 15 stations of fitting shop and verified the site operation, equipment security capacity, key points guarantee and personnel qualification and workpiece supply. I submitted 18 improvement requirements and constituted 10 measures which effectively enhanced availability rate of work area and process quality assurance ability.

　　My summary:

I am honest and faithful and smart. I have strong study ability and could bear hardships and have good group cooperation spirit. For contacting Japanese workers in daily work, I have learnt earnest and meticulous working ways from staff members of the Toyota. I form good work style and better knowledge structure.

Name: 范文稿 Gender: Male

Wedlock: Single Nation: Han

Residence: Guangdong-Qingyuan Age: 28

Location: Guangdong-Dongguan Height: 173cm

Target Locations: Guangdong

Target Positions: Industry/Factories-Industrial Engineer

Industry/Factories-Production Management Clerk

Industry/Factories-Technic Engineer

Target Jobs: Industrial Engineer、 Lean Engineer

　　Education

2005-09 ～ 2009-07 GuangDong University of Technology Industral Engineering Bachelor Degree

　　Training

2008-12 ～ 2008-12 Guopei Certificate Internal Quality Auditor Training &Qualification

【company name】 (2011-07 ～ Present)

Company Type: Private Enterprise Company Category: Electrical,Micro-electronics

Job Title: Industrial Engineer Positions: Industrial Engineer

Job Description: : process planning, fixture and equipment planning, prepare process checklist

dard time and capacity evaluation, line balance and prepare SOP for new products

tain the usage of the consumptive material, standard time and capacity

orm line balance and improve process to rise capacity

gn and improve the tools and fixture in the work site

tor the efficiency of the production line, analyze these reasons manpower, machine, material , environment, method, push the relative dept to solve issues

en project planning and push: Auto-machine introduce, production way optimize, manpower and material saving, etc

Career Highlight:

-welding machine introduce: welding process operator saving(16 operators-12 operators=4 operators), line balance rate upgrade from 83% to 91%, solder wire saving 3.2grams, cost of solder wire saving 1.6 yuan RMB for each PCBA.

-packaging production line planning and implement: master carton packaging operator saving, every production line deploy 2 packaging operators for 8 lines, after introduce the new equipment it takes only 5 operator to seal the master carton

cabinet pre-process and final assembly combine: manpower saving include 1 conveyer, 1 visual inspector, 1 loading operator and 1unloading operator(total 4 operators), and saving the usage of bubble bag and partition board

rative plate incoming package improvement: change the package material and simplify package way to reduce pack cost(from 0.13yuan to 0.09yuan RMB) and cut down unpack operation time( saving 12 seconds)

erate with RD to change PCBA process from dispensing process to solder paste process, in order to cut down welding failure rate after wave-soldering. In this case charge of PCBA fixture design and improvement evaluation(repairing welding time 140sec reduce to 70sec,4 repair welding operators cut down to 2 operators)

rding to the small order quantity of the product, study the less humanizing process for small products to reduce the change over loss time(38 operators*30minute-

20 operator*40minutes=340minutes) and improve 8% of the motion effective rate

Reason for Leaving: Not very good economic benifit of the company,little chance to promote both in position and welfare

【company name】 (2009-07 ～ 2011-06)

Company Type: Joint Venture Company Category: Electrical,Micro-electronics

Job Title: Junior Engineer Positions: Industrial Engineer

Job Description: blish and maintain the standard labor time, perform line balance to improve production capacity

capacity assessment: Base on the MPS and the capacity of production line to forecast the workforce requirement

are the cost study report for new products, labor rate evaluate basis on factory operating cost, provide quotation to customer for special process

are the workshop layout and line layout design basis on logistics analysis

arch and develop new packaging method, develop new suppliers for packing material, make order for new packing material and follow up the schedule

with customer complaint and settle products packaging issue, improve packaging method to satisfy customer

Career Highlight:

1. Function test man-machine operation improvement: cooperate with TE to disassemble

and rearrange test item, and modify the way of program display in the monitor, in order

to realize one person simultaneously operate two test machine

2. Line balance improvement: provide the cycle time of each model to set up assemble line speed, and upgrade the line balance rate to 80% above for all model

Reason for Leaving: Not a very good department to pratice and learn IE skill,seek more chance to enhance myself

　　Special Skills

Professional Title:

Computer Level: national computer exam. grade 3

Computer Skills: familiar with Windows，be good at Microsoft office software;

passed National Computer Rank Exam of database technology ;

ery in Auto CAD of computer aided design software;

Strengths: familiar with method study and standard time measurement, know well about Work study technology including 5W1H inquire skill and ECRS four principles

ery in IE seven techniques, comprehend production management essentials

And the activity about 5S.

familiar with logistics analysis during the production process, be capable of

Facility planning and machine layout

about the basis quality management tools, such as Seven QC Methods and FMEA technique

　　Language Skills

Chinese: Good Cantonese: Good

English Level: CET-4

English: Good

Career Objective

Career Direction: A position as IE engineer or Lean engineer which will use the IE concept and lean production to reduce the cost of enterprise running ,promote the competitive strength,as a result to achieve the win-win target with enterprise.

　　Requirements:

　　Self Info.

Self Assessment: elor degree in Industrial Engineering, have good sense in cost down, and have successful case of improvement

ed in Taiwan electronic company for almost two year, be familiar with SMT, DIP, repair welding, final assembly, test and packing process

ng hands-on skills, have experience in guiding operation for new production first MP

skill in Auto-CAD, can design and make fixture in the workshop

communication and organization skill in working with other department, have some experience in training

onsibility for work and a man of great loyalty, able to learn, patient and positive.